PIX software up to version 7.2(4) is supported. Trusted boundary (extended trust for CDP devices)Ī special version of Qemu called PEMU is embedded into GNS3 for emulating the PIX 525 Security Appliance.Spanning Tree Protocol (STP) – Uplink Load Balancing.Spanning Tree Protocol (STP) – Root Guard.Spanning Tree Protocol (STP) – Portfast Support for Trunks.Spanning Tree Protocol (STP) – PortFast BPDU Filtering.Spanning Tree Protocol (STP) – Loop Guard.Rapid-Per-VLAN-Spanning Tree (Rapid-PVST).QoS Policy Propagation via Border Gateway Protocol (QPPB).IP Phone Enhancement – PHY Loop Detection.IEEE 802.1X Multi-Domain Authentication.IEEE 802.1W Spanning Tree Rapid Reconfiguration.IEEE 802.1s VLAN Multiple Spanning Trees.IEEE 802.1s – Multiple Spanning Tree (MST) Standard Compliance.IEEE 802.1ab, Link Layer Discovery Protocol.Flex Link Bi-directional Fast Convergence.BGP Route-Map Continue Support for Outbound Policy.BGP Restart Neighbor Session After max-prefix Limit Reached.BGP Increased Support of Numbered as-path Access Lists to 500.Access Switch Device Manager (SDM) Template.Keep in mind that this module works differently (uses the vlan database etc.) and doesn’t support the following features: However you can use the EtherSwitch module with 2600s, 3600s and 3700s Series. This is due to the impossibility to emulate ASIC processors used in those type of devices. Online Insertion and Removal (OIR) is supported, allowing you to replace PAs while the router is running.Īt this moment, it is not possible to emulate Catalyst switches with Dynamips/GNS3. C7200-IO-GE-E (1 GigabitEthernet port, Ethernet port is not functional).NPE-G2 (requires the use of NPE-G2 c7200p IOS images).Note: VXR chassis, NPE-400 and C7200-IO-FE are the default in GNS3.Only the 7206 is supported, it has 6 Port Adapters (PA) slots.
#Gns3 router ios images serial#
NM slots: 4 (maximum of 32 FastEthernet ports or 16 serial ports).ħ200s have a different architecture.NM slots: 2 (maximum of 32 FastEthernet ports or 8 serial ports).Note: the 2691 is essentially a 3700 with 1 NM slot.NM slots: 1 (maximum of 16 FastEthernet ports or 4 serial ports).2 FastEthernet fixed ports (GT96100-FE).NM-16ESW (switch module: 16 FastEthernet ports, maximum of 2 modules per router)ģ700s have 2 FastEthernet interfaces on the motherboard, 3 subslots for WICs and 1 to 4 Network Module (NM) slots.NM slots: 6 (maximum of 24 Ethernet ports, 32 FastEthernet ports or 24 serial ports).2 FastEthernet fixed ports (Leopard-2FE).NM slots: 4 (maximum of 16 Ethernet ports, 32 FastEthernet ports or 16 serial ports).NM slots: 2 (maximum of 8 Ethernet ports, 32 FastEthernet ports or 8 serial ports).NM-IDS (IDS Network Module, not working).ģ600s have 2 to 6 Network Module (NM) slots.NM-NAM (Network Analysis Module, not working).NM-16ESW (switch module: 16 FastEthernet ports).2 FastEthernet fixed ports (CISCO2600-MB-2FE).
#Gns3 router ios images series#
But this Post is related to Gns3 IOS images for Router, there are many GNS3 IOS for routers but one of the most stable IOS image is Cisco 7200 series IOS. For switching features on GNs3 you are required Cisco IOS with NM-16ESW-module. Routerenable Router#conf t Enter configuration commands, one per line. This is my attempt to configure the router. I can configure single FastEthernet interfaces on each router but I need to have two per router. I’m doing a lab for my internetworking course and I’m using GNS3 as the emulator. In this way you can utilize the maximum of you RAM and can run the maximum number of routers in GNS3 as compare to any other IOS like 7200 series which required high RAM. Cisco 1700c is a very cool IOS for gns3 as it required a very little RAM.